Skip to main content

HSPCB Standards for Effluent Discharge into CETPs

Haryana State Pollution Control Board (HSPCB) Standards for Effluent Discharge into CETPs
Sanjaya K. Mishra, Editor & Publisher, Enviro Annotations
The Haryana State Pollution Control Board (HSPCB) has specified the inlet quality standards for the Common Effluent Treatment Plants (CETPs) in Haryana. These standards are established with due consideration of local needs and conditions. During the process of laying these effluent standards, the Board sought a proposal from the Technical Advisory Committee. The proposal was shared with all stakeholders on 29th December 2018 through acclaimed newspapers; inviting comments, suggestions or objections. According to HSPCB Order No. HSPCB/SSC/2019/6916-39 Dated 28/01/2019, the Board has considered all observations submitted by stakeholders, including industries and industrial associations, in response to the proposal. The units, which discharge their effluent into the CETPs, need to comply with the standards. The standards vary from place to place and detailed below.

S. No.
CETP Location
Outlet from Industry running to the Inlet of CETP
1.
Sector-29, Part-II, Panipat
pH between 6.0 to 9.0
Fixed Dissolved Solids (FDS): 2100 mg/l (if FDS in raw water is up to 1100 mg/l) or 3100 mg/l (if (if FDS in raw water is more than 1100 mg/l)
TSS: 275 mg/l
COD: 1200 mg/l
BOD: 500 mg/l
Oil & Grease: 25 mg/l
2.
Industrial Area, HSIIDC, Barhi, Dist. Sonepat
pH between 6.0 to 9.0
Fixed Dissolved Solids (FDS): 2100 mg/l (if FDS in raw water is up to 1100 mg/l) or 3100 mg/l (if (if FDS in raw water is more than 1100 mg/l)TSS: 1500 mg/l
COD: 1400 mg/l
BOD: 500 mg/l
Oil & Grease: 15 mg/l
3.
Industrial Area, HSIIDC, Rai, Dist. Sonepat
pH between 6.0 to 9.0
TSS: 450 mg/l
COD: 1000 mg/l
BOD: 250 mg/l
Oil & Grease: 35 mg/l
Phenolic Compounds: 3.75 mg/l
Zinc: 11.0 mg/l
Sulphides: 9 mg/l
4.
Industrial Area, HSIIDC, Kundli, Dist. Sonepat
pH between 6.0 to 9.0
TSS: 450 mg/l
COD: 550 mg/l
BOD: 250 mg/l
Oil & Grease: 15 mg/l
5.
Industrial Area, HSIIDC, Murthal, Dist. Sonepat
pH between 6.0 to 9.0
TSS: 450 mg/l
COD: 550 mg/l
BOD: 250 mg/l
Oil & Grease: 15 mg/l
6.
IMT Manesar, Dist. Gurugram
pH between 6.0 to 9.0
TSS: 900 mg/l
COD: 1100 mg/l
BOD: 550 mg/l
Oil & Grease: 75 mg/l
7.
Sector 37, Gurugram
pH between 6.0 to 9.0
TSS: 450 mg/l
Hexa-valent Chromium: 11 mg/l
Total Chromium: 26 mg/l
Zinc: 7 mg/l
Nickel: 11 mg/l
Iron: 9 mg/l
Copper: 7 mg/l
Cadmium: 0.75 mg/l
Lead: 0.75 mg/l
Arsenic: 0.75 mg/l
Total Metal: 26 mg/l
Cyanide: 6 mg/l
Phosphate: 11 mg/l
Fluoride: 11 mg/l
Oil & Grease: 22 mg/l
8.
Faridabad Electroplaters Association, Sector-58, Faridabad
TSS: 300 mg/l
Hexa-valent Chromium: 11 mg/l
Total Chromium: 22 mg/l
Zinc (Dissolved): 11 mg/l
Nickel: 7 mg/l
Iron: 7 mg/l
Copper: 7 mg/l
Cadmium: 1.5 mg/l
Lead: 1.5 mg/l
Arsenic: 0.75 mg/l
Total Metal: 30 mg/l
Cyanide: 15 mg/l
Phosphate (Dissolved): 11 mg/l
Fluoride: 15 mg/l
Oil & Grease: 22 mg/l
9.
Industrial Area, HSIIDC, Barwala, Dist. Panchkula
pH between 6.0 to 9.0
TSS: 150 mg/l
COD: 325 mg/l
BOD: 200 mg/l
10.
Industrial Area, HSIIDC, Ambala Cantt.
pH between 6.0 to 9.0
Fixed Dissolved Solids (FDS): 2100 mg/l (if FDS in raw water is up to 1100 mg/l) or 3100 mg/l (if (if FDS in raw water is more than 1100 mg/l)TSS: 150 mg/l
COD: 500 mg/l
BOD: 150 mg/l
11.
HSIIDC Saha, Dist. Ambala
pH between 6.0 to 9.0
TSS: 900 mg/l
COD: 1100 mg/l
BOD: 550 mg/l
Oil & Grease: 75 mg/l
12.
Industrial Area, HSIIDC, Jind
pH between 6.0 to 9.0
TSS: 175 mg/l
COD: 500 mg/l
BOD: 250 mg/l
Oil & Grease: 35 mg/l
13.
IMT, Rohtak
pH between 6.0 to 9.0
TSS: 900 mg/l
COD: 1100 mg/l
BOD: 550 mg/l
Oil & Grease: 75 mg/l

It is highly important to note that the individual industrial units need to comply with other parameters, which are not specified in the Board’s Order No. HSPCB/SSC/2019/6916-39 Dated 28/01/2019; but applicable to the industry. The industries may refer to the Standards and Legal Requirements for Electroplating and Anodizing Industries laid down by the Ministry of Environment, Forest and Climate Change (MoEF&CC), erstwhile Ministry of Environment and Forests, Government of India vide GSR 266(E) dated March 30, 2012. Enviro Annotations has deliberated on this notification in its 23rd Issue on 1st May 2019.

www.enviroannotations.com              Twitter            Blogger           Facebook

Comments

Popular posts from this blog

E-Waste Rules and Industries responsibilities

Introduction: E-waste or electronic waste is created when an electronic product is discarded after the end of its useful life. Some examples are discarded computers, office electronic equipment, entertainment device, electronics, mobile phones, television sets, and refrigerators. This includes used electronics which are destined for reuse, resale, salvage, recycling, or disposal as well as reusable and secondary scraps such as copper, steel, plastic, etc. The rapid expansion of technology means that a very large amount of e-waste is created every minute.
Legislations in India:


In India, prior to the enactment of the E-Waste (Management and Handling) Rules, 2011; e-waste was covered under the Hazardous Waste Management Rules. The E-waste (Management and Handling) Rules, 2011 were enacted on 12th May 2011 and became effective from 1st May 2012. These Rules were brought into force to enable recovery and/or reuse of useful material from e-waste, thereby reducing the hazardous wastes destined…

Boiler Emission Norms in India (Updated)

This blog has been published in the 14th issue of environmental weekly Enviro Annotations dated 27th February 2019. The article is contributed by Sunita Mishra, who has worked as In-charge of Technical Management in Ultratec Research & Analytik Labs and Management Representative of Eco Corporate.

Ministry of Environment, Forest and Climate Change (MoEF&CC) brought a Notification vide General Statutory Rules (G.S.R.) 96(E) on 29th January 2018 - for industrial boilers. Unlike the previous ones, this notification specifies standards and limits based on fuel used in the boiler. Earlier, the standards and emission limits were based on the steam generation capacity of a boiler. The norms specified are as follows:


The boiler used in the industries, namely (1) sugar (2) cotton textiles (3) composite woollen mills (4) synthetic rubber (5) pulp and paper (6) distilleries (7) leather industries (8) calcium carbide (9) carbon black (10) natural rubber (11) asbestos (12) caustic soda (13) s…

Procedure to Test Sound Level of Diesel Generators

Most of the business establishments, industrial units and also some housing complexes install diesel generators (DG) as a back-up to the erratic electrical supply. Such establishments should also know applicable regulations is the noise limit specified by regulatory body Central Pollution Control Board (CPCB, Ministry of Environment, Forest and Climate Change. One most important regulatory requirement is that all such DG sets must be provided with acoustic treatment. Another regulatory requirement is that the allowable limit of sound power levels (SPL) in case of DG sets up to 1000 KVA is 75 decibel in A-scale. While in case of DG sets up to 1000 KVA there is a requirement of minimum insertion loss of 25 dB(A) before and after acoustic treatment. The CPCB has also a specified procedure for the determination of SPL as to be carried out according to ISO: 8528 (Part 10), meeting the requirement of grade 2 accuracy. Any DG set without acoustic enclosure as per GSR 371(E) dated 17th May 20…